icsp - Microprocesadores y microcontroladores

Microprocesadores

http://www.automatismos-mdq.com.ar/blog/2008/12/aplicaciones-con-pic12c508.html

https://www.circuitsathome.com/tag/icsp

BobTech - Embedded Controls

http://www.bobtech.ro/catalog/programator

DescripciónCable programador de Arduino (sketches y bootloader) realizado modificando un cable de datos NOKIA CA-45 0 KU??. IntroducciónPara convertir el chip ATmega en un Arduino es necesario cargarle un "bootloader" o cargador, es decir, un programa inicial (utilizando un simil con un PC podríamos decir que es una BIOS) que nos facilite la conexión del Arduino con el PC. Con el bootloader instalado en el chip, el método de grabación de programas (sketches) en el Paperduino (Arduino), es .......

https://txapuzas.blogspot.com/2011/12/paperbootloaderftdi-cargador-de.html

MCP2502X/5XDescriptionThe MCP2502X/5X devices operate as I/O expandersfor a Controller Area Network (CAN) system, supporting CAN V2. 0B active, with bus rates up to1 Mb/s. The MCP2502X/5X allows a simple CAN nodeto be implemented without the need for amicrocontroller. The MCP2502X/5X devices feature a number ofperipherals, includ.......

https://basicelectronic.blogspot.com/2009/11/adc-and-io-can-bus-circuit.html

Author: Chaonan Chen, Huihui Duan, Au Group ElectronicsAu Group Electronics "3-in-1 Mini-lab"(part #: ML-3IN1) or "2-in-1 Mini-lab" (part #: ML-2IN1) is a handy, low cost tool capable of programming, debugging and testing Flash-based PIC Microcontroller, KEELOQ HCS, MCP250xx and EEPROMs. It can connect SMD or through hole chip.......

https://augroups.blogspot.com/2009/02/user-manual-for-2-in-13-in-1-mini-lab.html

Our purpose here is to explore the potential of PIC12F683 microcontroller for which we need a development board.The good thing is we are going to make our own board.The schematic and the actual board that I have built are shown below. I soldered all the components on a 12 x 8 cm general purpose prototyping board.Completed Board It has following features in it:1. A Regulated.......

https://picboard.blogspot.com/2010/02/make-your-own-pic12f683-development.html

Hola, hoy estaré realizando una actualización a la matriz de led 8x8 que posiblemente ya conozcan de mis otros post https://electgpl.blogspot.com.ar/2013/11/matriz-8x8-mensaje-con-desplazamiento. htmlEn este caso, no hay nada nuevo, solo he agregado unas secuencias de animación, texto scroll y dibujos estáticos. La idea era montarla en el árbol navideño junto a unas tiras de led RGB para hacer una navidad mas tecnológica. Me queda como pendiente (aunque no tengo demasiado tiempo para ello.......

https://electgpl.blogspot.com/2015/12/matriz-8x8-con-motivo-de-navidad.html

Hello, I'm here to talk about the Maple from LeafLabs.com, since some of my latest work has been on this board and processor. The MapleAs you probably know Arduino launched Arduino Due with an ARM processor a couple of months ago and since then it's been the talk of the interwebs, however, the Maple beat the Due to market by quite a long time. The big difference is that the chip used in the Maple is from ST whilst the .......

https://microsrus.blogspot.com/2013/06/maple-from-leaflabs-stm32-arm-board-in.html

Cambios: Se cambiaron las resistencias de 1/8w por resistencias de 1/4w mas comerciales.Cuenta con doble alimentación, USB-BUS y Externa, Sense PIn, Led Power, Led User, BUS ICSP y Reset. A esta placa se le puede colocar diversos bootloaders y trabajar con diferentes entornos, MIKROC, CCS, Pinguino, XC8........

https://electronicosembebidos.blogspot.com/2017/07/placa-entrenadora-power2550-con-micro.html

DIY Electronics projects and products.

https://www.circuitsathome.com/?p=2

This is 100W inverter circuit. It uses 4047 IC and IRF540 Mosfet instead of 2N3055 transistor. Power output is 100W from 2-3A transformer.

http://www.electronics-diy.com/electronic_schematic.php?id=661

PIC 18F4550 and 18F2550 are powerful microcontrollers including a full-speed USB V2.0 compliant interface. With these MCU it's very easy for the hobbyist to design USB devices with very few components. In these pages, I'm describing how to use the CDC firmware from Microchip . It permits to

http://www.radiolocman.com/shem/schematics.html?di=51860

http://arantxa.ii.uam.es/~acaf/Documentacion/Tema_III_Disenio_Circuitos_Pasivos_RF.pdf

Author: Chaonan Chen, Au Group Electronics(Discussion on DIY of CB0703 is now available at our forum)1. What you need:a. Bare printed circuit board (Part# CB0703)b. Schematic Drawing and Reference PCB assembly drawing of CB0703 (Both are free to download from https://www.auelectronics.com/ )c. All electronic components (all components are list in the schematic drawing, and are available from https://www.auelectronics.com/products/hardware/cb0703. html )d.Soldering toolsets, solder paste or liqui.......

https://augroups.blogspot.com/2009/02/step-by-step-assembly-guide-for-cb0703.html